A material description becomes much clearer when it names what sits beneath the surface. Leather fibres held together with a binder, a continuous split-leather layer with a coating, and a polyurethane-coated textile are different constructions. For a bag, belt or wallet, identify the base material, the surface treatment and the component being described before comparing labels.
Separate reconstituted fibres from a continuous leather layer
Competition Bureau Canada’s 2018 furniture terminology sheet distinguishes bonded material made from shredded leather fibres and a binder from bi-cast leather, which has a split-leather base and a polyurethane surface. The distinction concerns the underlying structure. The document’s furniture examples do not identify the construction of a particular accessory.
A manufacturer example makes the fibre process more concrete. Salamander’s Performa description identifies shredded leather offcuts combined with vegetable tanning agents, natural rubber, fats and water. It presents this material for footwear components. That formulation belongs to the named material; it is not a recipe for every product described as bonded or recycled leather.
In this terminology, “bonded” describes a reconstituted material. Merely learning that an accessory contains glued layers does not establish that it contains bonded leather. For the separate distinction between grain-bearing leather and a continuous lower split, see full-grain, corrected-grain and split leather.
Read PU together with the substrate description
PU stands for polyurethane, but the abbreviation alone leaves the base material unresolved. The Canadian sheet uses “PU leather” as another name for bi-cast leather. A description of a PU-coated textile, by contrast, should identify its textile backing. Keep the complete supplier wording rather than treating every use of PU as the same construction.
Ultrafabrics’ Pebble Caramello specification illustrates a layered declaration: a 100% polyurethane surface and a backing of 65% polyester and 35% rayon. Those percentages describe the named surface and backing separately. They are not a whole-material mass breakdown, and the upholstery specification is not evidence that any Möhel product uses that material.
| Description | Construction question | Useful detail to request |
|---|---|---|
| Bonded or reconstituted leather | Which leather fibres and binder form the material? | The named grade, composition and any surface or backing layers. |
| Coated split leather | What coating sits on the continuous leather base? | The substrate description and the finish specification. |
| PU-coated textile | Which fabric supports the polyurethane surface? | Separate surface and backing compositions. |
Keep backing, lining and component coverage distinct
When a specification names a material backing, record it with that material. When it names the bag lining, record the lining separately. Do not assume that a textile on the reverse of a supplied sheet is the same component as the fabric inside a finished bag.
A useful enquiry identifies the part: outer body, strap, trim, pocket or lining. For example, “leather trim” leaves the body material open, while a description of the exterior leaves the interior open. Ask the maker to map each material to a component rather than expanding one statement to cover the entire accessory.
If a recycled-content percentage is supplied, ask which layer or component it covers and how the percentage is expressed. Keep the supplied figure with its scope. A percentage alone should not become a claim about the whole bag, its expected lifespan or its suitability for a particular cleaner.
Build a material record before choosing care
- Save the exact label, product identifier and source. Photograph any accessible composition label without cutting or separating the item.
- Identify the component covered by each statement. Record substrate, binder or coating, backing and lining only where the maker provides them.
- Ask about unresolved wording, including what PU refers to and whether a percentage concerns one layer or the complete material.
- Obtain care instructions for the named finished item. Keep observed wear separate from confirmed composition, and retain any reply with the original description.
A smooth or embossed face cannot supply the missing layer declaration. Avoid peeling a surface or trying a solvent, flame or water-drop identification test on the accessory. If the material remains uncertain, use the questions in material-and-finish care before selecting a treatment.
Sources and scope
Sources were reviewed on 19 October 2026. The furniture terminology sheet and manufacturer specifications provide construction examples, not a universal quality ranking or a legal labelling assessment. The comparison table and recording sequence are editorial guidance. No material sample was analysed or wear-tested, and no historical Möhel material is identified by these examples.
Continue in materials and finishes guides.